Basics of radio

|=---------------------=[ The basics of Radio ]=-------------------------=| |=-----------------------------------------------------------------------=| |=------------------=[ shaun2k2 <shaun at rsc dot cx>  ]=----------------=|  0 - Introduction   0.1 - Technical Terms  1 - Radio Basics   1.1 - Radio Waves   1.2 - Carrier   1.3 - (RF) Frequency Bands   1.4 - Wavelength   1.5 - Transmission   1.6 - Receiving  2 - AM Radio   2.1 - What is AM Radio?   2.2 - Modulation   2.3 - Demodulation   2.4 - Circuits       2.4.1 - Receivers       2.4.2 - Transmitters  3 - FM Radio   3.1 - What is FM radio?   3.2 - Modulation   3.3 - Demodulation   3.4 - Circuits  4 - Misc   4.1 - Pirate Radio   4.2 - Wireless Telephone Tapping   4.3 - Jamming  5 - Conclusion  6 - Bibliography  --[ 0 - Introduction      Ever since our discovery of radio, in around 1902, we have proceeded to utilise it for many different purposes -- from sending others short messages, to transmitting large and critical data sequences to other computer systems.  As time has gone on, as useful a technology as radio is, it is barely noticed anymore.  When most people think of 'radio', they picture a small black device sitting in their car, which they will use to listen to their local radio stations during car journeys.  On the other hand, very few people realise the true usefullness of radio, often forgetting that their cellphones, televisions, satellite TV and alarm systems all too use radio to complete their task on a very regular medium -- radio is not just that boring old thing gathering dust in the corner.      This article is divided up into four parts.  The first part describes the basic theory of radio, and examples to illustrate some of the common day uses of it.  In parts two and three, AM and FM radio details are outlined showing various different circuits to illustrate how these principles can be applied to real-life, functioning circuits.  Section four is a misc. section, presenting some miscellaneous interesting points.  Some electronics knowledge is useful in radio, though not totally necessary.  Most circuits presented here are quite rough, and can be greatly improved upon in many ways.    ----[ 0.1 - Technical Terms  Below is a description of technical terms used throughout the article:   RF          -- Any frequency within the radio spectrum, which can be                used by to transmit and receive radio signals.  Modulation  -- A technique used to package data into a radio signal                which is of use to the destination radio receiver.  AM          -- Amplitude Modulation.  This involves shifting the amplitude                of a radio signal's carrier very slightly in sympathy with                a modulating signal.  FM          -- Frequency Modulation.  FM modulation involves shifting the                frequency of a radio wave's carrier very slightly in                sympathy with a modulating signal.  Receiver    -- Any device which is capable of receiving radio signals                sent by a radio transmitter.  Transmitter -- A device which can transmit radio waves into the                surrounding environment.  Aerial      -- A medium to large piece of wire which is used by either a                radio transmitter or receiver to propagate or detect an                incoming radio signal.  In a radio receiver or transmitter,                an aerial acts as one plate of a capacitor, whilst the other                plate is taken place by the Earth.  Antenna     -- See aerial.  Wireless    -- Refers to any technology which communicates data without the                need for a wired connection.  Most wireless devices, such as                cell phones, televisions, and others use radio, but several                do use technologies such as infrared, which is not covered                here.  Radio wave   -- A radio wave is an 'electromagnetic' wave, most commonly                 containing data to be received by a remote radio receiver.  Oscillator   -- Refers to an electronic circuit which 'oscillates', or                 'vibrates', to complete a certain task.  Oscillators are                 used in radio to transmit radio waves at a given                 frequency -- the rate at which the oscillator oscillates is                 the RF (see RF) at which the wave is transmitted.  Common                 oscillator circuits, also used in this paper, are LC                 oscillator circuits, and crystal-controlled oscillators.  Crystal-controlled oscillator   -- An oscillator circuit whos oscillation frequency is                 controlled by a 'crystal'. See oscillator.  LCoscillator -- An oscillator consisting of a capacitor and an inductor,                 whos frequency of oscillation is controlled directly by the                 capacitor, which is usually variable.  See oscillator.  Capacitor    -- Device which stores current as an electrical field.  Broadcast    -- A term used to describe transmitting radio waves into the                 atmosphere.  Wavelength   -- The physical distance between two waves on the same                 frequency, transmitted successively.  Bands        -- Frequency Bands are a range of frequencies used                 interchangeably or commonly for the same type of technology.                 For example, televisions often use the VHF band.  Frequency    -- Number of cycles per seconds. Frequency can be used to                 describe how often an oscillator oscillates.  Sidebands    -- When modulation of a carrier is applied, two extra                 bands are generated, both slightly higher and lower                  than the carrier frequency, equating from the 'sum and                  difference' of the carrier and audio                 frequency.  These two bands appear at either end of                 the RF carrier, hence the term 'sidebands'.     --[ 1 - Radio Basics  ----[ 1.1 -  Radio Waves      Radio waves, otherwise referred to as 'radio signals', are simply electromagnetic waves.  Radio waves are transmitted by devices called 'radio transmitters' or 'transmitters' for short.  Despite our wide and many uses for radio waves as a whole, we actually known very little about 'radio'.  We do know, however, that radio waves are a form of energy, which act exactly like they have been propagated as any other type of wave we know of. For example, an audio wave.      Radio waves are made up of three things; an electric field, a direction, and a magnetic field.      Despite our underlying ignorance of radio and its properties, we can predict and use its properties to our advantage to undergo a wide variety of different tasks -- and will probably do so for a long time to come.   ----[ 1.2 - Carrier      An 'RF carrier' can be thought of as the part of the radio wave which can be modulated to 'carry' a data signal. An analogy to help with understanding this is to think of turning on a flashlight and pointing it towards a wall.  The light which is seen on the wall is the 'carrier'.      Before and without modulation, the carrier of a radio wave contains no data, and just contains peaks of an RF voltage.                            peak voltage                         ||\\    ///\    //\\                        || \\  //  \\  //  \\                        ||  \\\/    \\\/    \\                               RF carrier       Because sending radio waves with a carrier containing no data would be almost useless, a carrier is 'modulated' to contain data. There are various modulation schemes in wide use, but the two most common schemes are AM (Amplitude Modulation) and FM (Frequency Modulation). These are discussed later.   ----[ 1.3 - (RF) Frequency Bands      As we can gather from listening to a variety of radio stations, different forms of technology use an entirely different 'band' of radio frequencies on which to send and receive their radio signals.      The entire range in which radio signals are transmitted extends from around 30KHz, up to about 30GHz.  This whole range of available RFs (Radio Frequencies) is known as the 'radio spectrum'.  The radio spectrum's range of frequencies, and their concurrent uses are shown in the below table.  +-------------------+----------------------------+---------------------+ | Frequency         | Uses                       | Name                | +-------------------+----------------------------+---------------------+ | 30KHz-300KHz      |   Long-wave radio, useful  | Low Frequency (L.F) | |                   |   for long distance        |                     | |                   |   communications           |                     | +-------------------+----------------------------+---------------------+ | 300KHz-3MHz       |   Medium wave, local radio | Medium Freq (M.F)   | |                   |   distant radio stations   |                     | +-------------------+----------------------------+---------------------+ | 3MHz-30MHz        |   Short wave radio         |  High (H.F)         | |                   |   Communications           |                     | |                   |   Amateur radio            |                     | +-------------------+----------------------------+---------------------+ | 30MHz-300MHz      |   FM Radio                 |  Very High (V.H.F)  | |                   |   Police radio             |                     | |                   |   Meteorology Comms        |                     | +-------------------+----------------------------+---------------------+ | 300MHz-3GHz       |   Air Traffic Control      |  Ultra High (U.H.F) | |                   |   TV                       |                     | +-------------------+----------------------------+---------------------+ | 3GHz-30GHz        |   Radar Comms              |  Microwaves (S.H.F) | |                   |   Satellites               |                     | |                   |   Telecommunications (TV & |                     | |                   |   telephone)               |                     | +-------------------+----------------------------+---------------------+       Since certain frequency bands are used to accomodate important communications, such as the VHF band, it became illegal to transmit radio waves at certain frequencies without a license. It was made so because transmission of radio signals at important frequencies could interrupt critical communication, such as communication between police officers with their radio transmitter devices.      All frequencies within the radio spectrum are invisible to humans. Light frequencies which are visible to humans, i.e frequencies which are present in the light spectrum, operate at *much* lower frequencies.   ----[ 1.4 - Wavelength      Wavelength is the physical distance between a peak in one radio wave, to the peak in another radio wave transmitted successively -- on the same RF.  As a general analogy, the wavelength can be thought of as the distance that the peak in a given wave will have travelled in the space of time for one cycle. This can be calculated using the below simple formula.  |\ = V / F  * |\ = lamda   V  = Velocity   F  = Frequency      Using this formula, the wavelength for an example scenario can be calculated, when the RF is 27MHz.  The speed of light is 300 million meters/second, which is therefore the velocity of the electromagnetic wave.  |\ = 300,000,000 / 27,000,000  = 11.11r      Looking at the above calculation, what can be gained? It seems that the wavelength for waves transmitted in the example scenario is 11.11 (recurring) meters, so from this, it can be gathered that a peak in a particular radio wave will have travelled 11.11r meters in the time it took for one oscillation of the transmitting oscillator. But how can we know how long this oscillation period takes? We can calculate this using the formula '1 / f'.  1 / 27,000,000 = 0.0000000370r      This means that within the miniscule time frame of 0.0000000370 (recurring) seconds, the peak within the radio wave should have travelled approximately 11.11 (recurring) meters.      Wavelength might seem quite a useless thing to calculate on its own, but it comes in very useful when it comes to calculating suitable aerial lengths for both radio transmitters and radio receivers. As a rule of thumb, an ideal length for a radio aerial is around 1/2 of the signals wavelength. This can be calculated very easily.  11.11 / 2 = 5.555 (roughly)      From this calculation, we can gain the knowledge that a near ideal radio transmitter/receiver aerial can be constructed to be of around 5.5 meters. Exact precision is not generally critical to the overall operation of the radio transmitter/receiver. For example, where portability of equipment is more of a concern than great efficiency, 1/4, 1/8 or even 1/16 of the wavelength in meters is often used for the length of the radio aerial.  11.11 / 4 = 2.7775 11.11 / 8 = 1.38875 11.11 / 16 = 0.694375      From this little experiment we can see that we can turn a length which is considerably out of question due to portability desires, into a length which is much more suitable, yet efficiency is not affected too much.      This technique is very commonly employed to calculate sensible lengths for radio aerials.  However, other techniques are also employed, especially in the case of satillite TV.  Notice how TV satillite dishes house tiny holes in the body of the dish? These holes are specially sized to ensure that radio waves with wavelengths less than that associated with the desired RFs (3GHz-30GHz) do not create an electrical current in the aerial wire, as suitable radio waves do. Holes based upon the same principle can also be found when looking inside a microwave oven.  ----[ 1.5 - Transmission      Perhaps one of the most difficult concepts to grasp in radio is how radio waves are actually broadcast into the environment. As touched upon previously, radio waves are transmitted using oscillators in electronic circuits, and the rate at which the oscillator oscillates is the frequency at which the radio waves are transmitted.      As an example, we will focus on using an LC tuned oscillator circuit in the radio transmitter circuit.  LC oscillators are made up of an inductor (L), and a capacitor (C).  If we consider how a capacitor stores current, we can come up with the conclusion that it is stored as an electric field between two plates -- these two plates make up the capacitor. During one oscillation (also known as a 'cycle') of the LC tuned circuit, all available current is stored first in the capacitor as an electric field, and then as a magnetic field associated with the LC circuit's inductor.  After a *very* short time period (1/f), the magnetic field is turned back into an electrical current, and begins to recharge the capacitor again.  Because the inductor's magnetic field is beginning to change back into electrical charge, the inductor turns another electrical field into a magnetic field in order to counter-act the change. This continuous cycle of quick changes keeps the current in the LC circuit flowing in the same direction, driven by the current stored in the inductor. When the inductor's charge eventually becomes zero, the capacitor becomes charged again, but with the opposite polarity. After each oscillation (cycle), energy loss has occured, but not all of the energy loss can be accounted for as energy lost as heat from the inductor's coil. Thus, we can gather that some energy has been 'leaked' from between the capacitor's plates, as electromagnetic energy -- radio waves.      If we consider this, we can conclude that the further apart the plates in the capacitor are, the more energy is broadcast ('leaked') as radio waves.  This must mean that if we have a capacitor with plates spaced 1 meter apart, more energy will be broadcast as radio waves than if the capacitor had plates spaced a very small distant apart. By thinking even deeper, we can conclude that to maximise 'leakage' of radio energy, a capacitor is needed in the LC tuned oscillator circuit with plates spaced at quite a distance apart.  It just so happens that for this task, to maximise broadcast of radio waves, the world's largest plate can be used to take the place of one plate of the capacitor -- the Earth!  The other capacitor plate needs just be a suitably lengthed piece of wire, which is an equally common sight -- this piece of wire is known as an 'aerial'!      In real-world radio transmitters, oscillator circuits are used to make a small current 'oscillate' in an aerial wire.  Because of the constant change of energy form in the oscillator circuit, the current oscillating in the length of the wire becomes electromagnetic and is radiated as radio energy.      Back to the length of the aerial in relation to wavelength; this is where the length calculated earlier comes in handy. From the knowledge gained here, we can assume an adapted LC oscillator circuit as below.                  Capacitor           Inductor               ________________             |                )             |                )            ---               )____________  Aerial            ---               )             |                )             |________________)       As a concept, using the adapted LC tuned oscillator circuit above, the transmission of radio waves can be thought of like this; radio waves are generated due to the propagation of an electric current in an aerial wire. It is, as we have learnt, the 'leakage' of electromagnetic energy from between the two plates of the capacitor which causes broadcasting of radio waves.       As oscillations occur in our LC tuned circuit, all available energy is stored in the capacitor, followed by energy (electrical current) not leaked as electromagnetic waves being fed into the inductor.  This whole process measures one oscillation, and once one oscillation is over, the whole process repeats itself again, and each time energy is being lost as radio waves from the acting 'capacitor' (aerial and Earth). Therefore, it is the rate at which the LC circuit is oscillating (the 'frequency') at that determines the frequency at which the radio waves are broadcast at -- thus determining the RF of the radio signals.  ----[ 1.6 - Receiving      The concept of receiving radio signals is based upon almost the opposite of the concepts of transmitting radio waves. In similarity to radio transmitters, radio receivers also use an aerial, but for a totally different purpose; for detecting the radio signals in the environment. As described previously, radio waves are a form of energy, propagated as electromagnetic waves through the air. Thus, when radio signals transmitted by nearby radio transmitters pass the aerial of the receiver, a *tiny* RF alternating current is generated in the aerial wire.  When a signal becomes present in the aerial wire, 'wanted' radio frequencies are 'selected' from the assortment of RF currents in the aerial, using a 'tuned circuit'.      As an example, we'll focus on the LC tuned circuit as in the previous  section, due to the simplicity of this circuit. RF current of the 'wanted' frequency can be selected from amongst the other RFs by use of an LC tuned circuit, which is set to resonate at the frequency of the 'wanted' radio frequency.  This selection is done because the LC tuned circuit has low impedance at any frequencies other than the 'wanted' frequency. Frequencies other than the 'wanted' frequency are prevented from passing through the circuit because they are 'shorted out' due to low impedance of the LC circuit at any other frequency than the resonant frequency (the frequency of the 'wanted' signals).      Following the selection of correct radio frequencies from the other RF signals, the radio receiver will usually amplify the signal, ready for demodulating.  The technique which is adapted by the receiver for demodulating the radio signal into the modulating signal is totally dependant on the type of modulation being used in the received radio wave.  In the case of an AM radio receiver, a selected signal will be 'rectified' and thus demodulated, using a low-drop germanium diode. This process basically turns the alternating RF current back into a direct DC current, which represents the power strength of the AM signal.  Next, the RF component is generally removed by using a capacitor. The output product of this process is a recovered modulating signal which can be fed to a pair of high impedance headphones.  The diagram below represents how the selected RF current is rectified by the diode.                                                          ||\\  //\\ ----------------------|>|--------------- ||\\ //\\   || \\||  \\                                         || \\||  \\   \/\/\/\/\/\/  AM Modulated Carrier  diode                     Modulating signal                                               (RF carrier present)       After being rectified by the diode, the AM radio signal is still not suitable to be fed to an audio output, as the RF carrier is still present. The RF carrier can be removed by using a single capacitor.                                      | | ||\\  //\\  ------------------------| |---------------------  /\  /\ || \\||  \\                         | |                      /  \/  \  Modulating signal                  capacitor          Modulating signal                                                     (RF carrier removed)       The output of the capacitor is a recovered modulating audio waveform which is suitable for passing to an audio output device, such as a set of headphones with a high impedance.      This technique is likely to be the simplest way to create an AM radio receiver, commonly known as the 'crystal set', used by the mass in the 1920s.  Other receivers are more often used to produce a higher quality of audio output, such as TRFs (Tuned Radio Receivers) and Superhetrodyne receivers.      The whole system model of a radio receiver at its most basic level can be thought of as the below diagram.            Modulated Radio Signal (electric current generated in aerial wire by radio wave)                   |                  \|/             Signal amplified                   |                  \|/            Signal demodulated                   |                  \|/           Modulating signal       Although the techniques and components needed to achieve each step of the diagram are different, most receivers stick to this sort of system.  Other types of receivers and their circuits are discussed more indeph in the section they are related to.   --[ 2 - AM Radio  ----[ 2.1 - What is AM Radio?      AM Radio refers to any form of technology which makes use of Amplitude Modulation to modulate the 'carrier' with information. To package a radio wave with often complex signals, the carrier of a radio wave is shifted in power very slightly in sympathy with a modulating audio or data signal. Next to morse code, AM is one of the simplest forms of modulation, and with this, comes its disadvantages.  ----[ 2.2 - Modulation       AM Modulation involves nothing more than shifting the power of a radio wave's carrier by tiny amounts, in sympathy with a modulating signal. Amplitude, as you probably already knew, is just another word for 'power'.       The simplicity of AM modulation can be demonstrated with a simple diagram like the one below.   ||\\    ///\    //\\ || \\  //  \\  //  \\  --->  \  /\  /  --->     \\    \\ ||  \\\/    \\\/    \\        \/  \/            \\ ///\\                                                 \\// \\                                                       RF Carrier            Modulating signal        AM signal        As you can hopefully make out from the diagrams, whenever the modulating signal (the signal which we are modulating) increases in voltage, the amplitude (power) of the RF carrier is increased in sympathy with the modulating signal.  When the voltage of the modulating signal declines in voltage, the opposite of above happens.  After AM modulating the carrier, the signal has usually twice the 'bandwidth' of the original modulating signal.   ----[ 2.3 - Demodulation      When an AM designed radio receives a radio wave, as previously noted, a small RF alternating current is generated in the aerial wire.  Because of the AM modulation of the carrier applied by the sending transmitter, the voltages in the carrier are larger and smaller than each other, but in equal and opposite amounts.  As a result, to recover the modulating signal, either the positive or the negative part of the modulated signal must be removed. In the simplest AM radio receivers, the modulated signal can be 'rectified' by making use of a single germanium low-drop diode.     \\/\/\/\/\  \\  /// //    ---------------------|>|----------------- \\  ///  //   \\// \\/                                                \\// \\//                                                     AM radio signal                  diode         Modulating signal        Here, part of the carrier has been removed, resulting in recovery, or 'rectification' of the modulating signal.      Because the carrier frequency (the RF of the radio wave) is usually significantly greater than the modulating frequency, the RF carrier can be removed from the resultant modulating signal, using a simple capacitor.   \\        //                   |  |  \\  ///  //    ----------------|  |----------------  \  /\  /  \\// \\//                     |  |                   \/  \/   Modulating signal           capacitor             Modulating signal (with RF carrier)                                (without RF carrier)       By exposing the rectified signal to a capacitor, the audio signal (or otherwise data signal) is smoothed, producing a higher quality of audible output.  At this point, the modulating signal is more or less recovered.      Although this technique of AM demodulation can be made to work to a satisfactory level, the vast majority of commercial radio receivers now adopt a design known as 'superhet', which I will explain briefly here.      Superhet receivers are based upon the principle of 'mixing' two signals to produce an intermediate frequency. The diagram illustrates a superhet receivers operation.   Carrier in ---> Tuned circuit  ---> Mixer ---> IF amplifier ---> Detector                (selects correct RF)    |                           |                                       |                           |                                        |                           |                                Local oscillator               Audio Amp                                                                   |                                                                   |                                                                 +--+                                                                 |  |                                                                 +--+                                                                 \__/                                                            As we can see, superhet demodulation is significantly more complex than 'rectification'.  Superhet receiver systems, like the above system diagram, works basically as follows.  First, an RF alternating current becomes present in the circuit, because of the electromagnetic activity around the aerial.  Signals of the correct radio frequency are selected via a tuned circuit, and inputted into one input pin of the 'mixer'.  In the meantime, the other input of the mixer is occupied by the 'local oscillator', which is designed to be oscillating at a frequency just lower than the inputted radio frequency. The output of the mixer is known as the 'Intermediate Frequency' (IF), which is the difference between the local oscillator frequency, and the frequency of the received AM radio signal. Next, the 'IF' is amplified, and passed to an 'envelope detector'. The output of the envelope detector is the modulating audio signal (an AF -- Audio Frequency), which is in turn amplified, and outputted to the user via a loudspeaker or other audio output device.      Since the local oscillator is almost always set to oscillate at a frequency of approximately 465KHz *below* the frequency of the carrier input, the output of the mixer will always be a 'carrier' of 465KHz -- which still carries the modulated information.  After the signal is amplified by the IF amplifier(s) (there can be more than one IF amplifier), the signal is now demodulated by the detector -- which is often just a single diode.  As mentioned above, the modulating signal recovered by the system can be fed to an amplifier, followed by an audio output device.      As well as producing a higher quality of audio signal, superhet receivers also eliminate the need to be able to tune multiple tuned circuits in a TRF (Tuned Radio Receiver).  TRF designs become awkward when it comes to tuning them into different radio frequencies because of the many tuned circuits needed -- superhets overcome this problem as they always 'know' what the collector load will be -- a 465KHz signal. Superhet designs can also be adapted to work with FM radio signals, assuming the 'detector' is changed to a suitable detector for FM signals (i.e phase detector).   ----[ 2.4 - Circuits      Since radio technology is a frequently discussed topic across the Internet, many radio circuit design implementations are readily available, ranging from very simple circuits, to quite complex ones. Here I present some radio related circuits which most people with a bit of electronics knowledge and the right components can build.   ------[ 2.4.1 - Receivers      Discussed above was the historic 'crystal set' radio receiver, which allows anyone with a long enough aerial wire and a few components to listen to AM radio bands.  Below is the basic crystal set radio receiver circuit, which is very easy to construct.       Aerial Wire             D1 *         |            Q1         |               ____|>|__________________         |_____________|/             |          |         |             |\             |          |  _______|_____          |            |          | (             |         |            |          | ( L1         --- C1 *   |        C2 ---         0  high impedance (            ---        |           ---         0  headphones (             |         |            |          | (_____________|         |            |          |         |               |            |          |         |_______________^____________|__________|         |               | (not joined)         |_______________|         |        GND  - C1 should be a variable capacitor to allow the station to tune into   other frequency bands.  - D1 should be a low-drop germanium diode -- non-germanium diodes   won't work.       From previous discussion, we can figure out that the above 'crystal set' AM radio receiver works as follows; incoming radio waves generate a tiny alternating current in the aerial wire, from which 'wanted' radio frequencies are selected, by the tuned LC circuit. Selected current passes through a diode, which 'rectifies' the signals, thus demodulating them. Before the diode, there is a simple transistor, which amplifies the 'wanted' frequency. The only reason for this is to make the quality of sound slightly better. Any remaining RF components are removed using a single capacitor -- this consequently has the effect of smoothing out the signal. The product audio signal is passed to a set of headphones -- these *must* be high-impedance, or nothing audible sounds on the headphones.      As was noted earlier, this type of receiver was used frequently in the 1920s, and gave even newbie electronic enthusiasts of that time the opportunity to build something that would be considered very useful at that time.  To make decent use of the 'crystal set' circuit, around 60-70 turns of wire around a rod of ferrious metal would create a good aerial.      Designs like above are never used in commercial radio receivers anymore. Excluding superhet receivers, TRFs are occasionally used to produce low quality radio receivers. Below is a simple TRF receiver schematic.                    Aerial             |              C5*   C6   +9V            |        ________________________________________            |        |     |    |       )                    |            |        |    ---  ---      )  LC2              |-|            |        |    ---  ---      )                 __| |            |        |     |____|_______)                 | |_|            |        |        |                           |  |   C8           ---  C1   |        |            D1     C7      |  |___| |____0           ---      _|_     Q1_____________|>|________| |_|_|/   | |    0   LC1      |    R1 | |      /                  |     | |   |\ Q2   _________|__     |_|  __|/                   |            |  High impedance   |           )     |  |  |\_____              |            |  headphones   |           )     |  |        |              |            |   |           )     |  |        |              |            |  ---  C2 *    )___| |__|_       |              |            |  ---          )   | |    |      |              |            |   |           )   C3     |      |              |            |   |___________)          |      |    C4        |            |                          |      |_____         |            |                          |      |    |     R4  |-|      R6 |-|                     R2  |-| R3 |-|  ---        | |         | |                         | |    | |  ---        |_|         |_|                         |_|    |_|   |          |           |                      ____|______|____|_________ |___________|                                        0V   - C2 should be a variable capacitor - C5 and C6 should be variable capacitors - Resistors of sensible values should suffice - Capacitors of sensible values should suffice        As in the 'crystal set' receiver, when a radio signal is 'picked up' by the aerial, the proper frequency is selected using the LC tuned circuit.  The signal is passed to a transistor amplifier.  However, this time, the transistor amplifier has a 'tuned collector load', because of the tuned LC circuit (LC2) at the collector leg of the transistor.  Next, the signal is rectified, stored in a few capacitors until enough current has collected, and is eventually fed to the user with the high impedance headphones.  The use of the tuned collector load at the transistor causes for the receiver to be more precise, amplifying only the signals which are at the frequency of LC2's resonant frequency.  As expected, this causes for a higher quality of audio signal to be fed into the users headphones, making this a much better radio receiver.       A few things can be done to improve the above receiver, such as adding yet more tuned amplifiers, and perhaps adding a few more resistors and capacitors for safety and efficiency purposes.    ------[ 2.4.2 - Transmitters      All that we really need to do when designing a simple radio transmitter is keep in mind that we require an oscillator -- either tuned or crystal controlled -- and a series of amplifier circuits which boost our signal. After these stages, all that is left is to make the signals oscillate in the aerial wire.  Below is a simple radio transmitter schematic.                                                                                                                         Aerial                                                                       |                                                                      |   ___________________________________________________________________|  |                        |                 |       |         |      |  |                        |                 |       |         |      |  |                     L1 )                 |       |         |   L3 |  |                        )          R3    |-|   C3 |         |__    ) |-|  R1   Crystal         )                | |     ---        |  |   ) | |_________|_____________)                |_|     ---        |  | C5) |_|        |||            |                 |       |         | ---  )  |                        |_______| |_______|_AM ___|_______|/  ---  |  |                       /        | |         Modulator     |\___|___|  |__________| |________|/         C2                      Q2    |    |  |          | |        |\   Q1                          (PNP)   |    )  |          C1           |                                     ---   )  |                      |-|                                 C4 ---   )  M                      | |  R4                                 | L2 )  |                      |_|                                     |    |  |                       |                                      |    |  |                       |                                      |    |  |_______________________|______________________________________|____|   - TR2 is a PNP transistor - M is a microphone      This circuit works by oscillating at the frequency controlled by the crystal (27MHz would be legal in the UK), amplifying the signal with tuned collector loads at the transistor (TR1), and then by radiating the signal off as radio waves by oscillating the signal in the aerial wire. Amplitude modulation is added to the signal by varying the gain of the transistor driver, by connecting it to the output of a microphone. The above circuit is quite inefficient, and is likely to produce low quality signals, but it can be used as a starting point to building a simple AM radio transmitter. It's probably illegal to operate the above circuit on frequencies requiring a license, so some countries *require* the circuit to be crystal controlled on a 'model radio' RF.  One improvement to be made on the schematic is to amplify the output of the microphone before feeding it to the transistor driver.      Possible devices which could apply the AM modulation are audio amplifiers, or even op-amps.  An audio amp following the oscillator would produce a higher quality, stronger signal, but would also provide power gain (i.e amplitude gain), in sympathy with the audio signal produced by the microphone.  This gain of amplitude due to the audio amp has essentially applied Amplitude Modulation of the carrier signal, because the power of the signal has been altered according to the inputted audio signal (at the microphone).  An ordinary op-amp could be used in a similar way, but by substituting the non-inverting input pin with a suitable power supply.  Essentially, this would cause for an outputted gain from the op-amp, according to the audio signal, because the two inputs to the op-amp are compared, as such.    --[ 3 - FM Radio  ----[ 3.1 - What is FM radio?      FM radio just means any form of technology which makes use of radio with FM modulated signals. To modulate a radio wave's carrier with information, FM transmitters shift the frequency of the carrier very slightly, to be in sympathy with a modulating signal.   ----[ 3.2 - Modulation      FM modulation consists of little more than shifting a radio wave's carrier frequency very slightly in sympathy with a modulating signal's frequency.  Modulation of an example audio signal is shown in the figures below.   ||\\    ///\    //\\ || \\  //  \\  //  \\  --->  \  /\  /  --->       ||\\  /\\  // ||  \\\/    \\\/    \\        \/  \/              ||\\ //\\ //                                                   ||\\// \\//                                                       RF Carrier            Modulating signal        FM signal      The diagrams show that when the frequency of the modulating signal increases, so does the given carrier frequency, and the opposite when the modulating signal's frequency decreases. This is shown in the FM signal diagram by the bands being spaced widely apart when the modulating signal frequency is increasing, and more closely together when the modulating signal's frequency is decreasing.   ----[ 3.3 - Demodulation      When an FM modulated carrier signal is detected by the receiver's aerial wire, in order to recover the modulating signal, the FM modulation must be reversed.      Most modern FM radio receivers use a circuit called the 'phase-locked loop', which is able to recover FM modulated radio signals by use of a VCO (Voltage Controlled Oscillator), and a 'phase detector'. Below is the system diagram of a PLL suitable for use in FM radio receivers.       FM signal in -------------> Phase  ---------------                                 Detector             |                                   |                  |                                   |                  |                                   |                  |                                   |                  |                                  VCO                 |                                    |__________________|                                                      |                                                      |                                                      |                                                      |                                                      |                                             Modulating signal                                                    out       The above PLL is able to recover the modulating signal by having one input to a phase detector as the modulated carrier, and the other input as a VCO oscillating at the frequency of the RF carrier. The phase detector 'compares' the two frequencies, and outputs a low-power voltage relative to the difference between the two 'phases', or frequencies. In essence, the outputted voltage will be relative to the frequency by which the carrier's frequency was shifted during modulation by the transmitter.  Therefore, the output of the PLL, known as the 'phase error', is the recovered modulating signal. In addition to being outputted from the small system, the voltage is also given to the VCO as 'feedback', which it uses to 'track' the modulation.  Acting upon the feedback received, the frequency of oscillation is altered accordingly, and the process is repeated as necessary.      In the past, less efficient and reliable circuits were used to demodulate FM radio signals, such as the 'ratio detector'. Although the 'ratio detector' is less sophisticated than PLL methods, a functioning ratio detector circuit is actually a little more complex than PLLs.      It should be noted that superhet receivers, touched upon a little earlier, can also be used as FM radio receivers, but their 'detectors' are different to that of an AM superhet -- for example, a PLL circuit or ratio detector discussed here could be used in conjunction with a superhet receiver to make an FM radio. This is the method which is actually adopted by most commercial radio receiver manufacturers.  ----[ 3.4 - Circuits   ------[ 3.4.1 - Transmitters      The same general principles apply to FM radio transmitters as they do to AM radio transmitters, except that information must be modulated in a different way.  In AM radio transmitters, the carrier frequency is more or less always constant.  However, in FM transmitters, the whole principle is to alter the carrier frequency in small amounts. This means that a tuned oscillator circuit is not appropriate, because we need to alter the frequency accordingly, not transmit at one static frequency.  The method used to overcome this problem is discussed a little later. A simple FM transmitter schematic diagram is presented below.                                                                       Aerial                                                                        |                                                                        |                                                                        |    ____________________________________________________________________|   |                               |                 |    |      |      |   |                               |                 |    |      |      )   |                               )                |-|  --- C3  |      )   |  R1                      L1   )             R3 | |  ---     |_ C4  )  |-|                              )                |_|   |      | |    )  | |                              )                 |    |      | ---  |  |_|               |   Crystal    |         C2      |    |      | ---  | L2   |_______________|||_____________|___________| |___|____|____|/   |   |   |                              /            | |             |\___|___|    |____________| |_____________|/                                      |   |            | |             |\  Q1                         Q2       |   |                              |                                     |   |            C1                |                                     |   M                             |-|                                    |   |                             | | R2                                 |   |                             |_|                                    |   |                              |                                     |   |______________________________|_____________________________________|       When audio signals are produced by the microphone, current carrying audio frequencies are amlified, and are used to modulate the radio wave.  Since the microphone does this all for us, there is no need to use modulation modules, ICs, or other technology.  In situations where an elecret microphone is not available to do the modulation for us, a varactor diode can be used to vary the capacitance in an oscillator circuit, depending on the amplitude of a modulating signal.  This varies the oscillation frequency of the oscillator circuit, thus producing FM modulation.    --[ 4 - Misc  ----[ 4.1 - Pirate Radio      Pirate Radio stations are simply just radio stations ran by individuals who are not licensed amateur radio enthusiasts.  Although radio is actually a natural resource, it has been illegal for a significant amount of time in some countries to transmit radio waves on certain frequencies.  Although transmitting radio signals on certain frequencies (around 27MHz) is legal in places like the UK, strict FCC regulations kick in, almost limiting the threshold to useless.  Because of this limitation, radio enthusiasts all around the globe see fit to set up pirate radio stations, which they use for their enjoyment, playing their favourite music tracks to the 'public', and for a breeding ground for aspiring DJs.  Some 'pirate radio' stations keep within the FCC terms, by transmitting at low-power. These types of stations are often referred to as 'free radio', or 'micropower stations'.      The legality of pirate radio stations is questionable, but varies from country to country.  In some European Countries, you can be arrested for just owning an unregistered transmitter.  In Ireland, prosecution rarely takes place if registered radio stations are not affected, but it is still illegal.  The US allows transmission of radio signals at *microscopic* power, making the limitations almost useless for unlicensed radio enthusiasts, thus causing them to resort to pirate radio.      Contrary to popular belief, setting up a pirate radio station is not necessarily a difficult task.  At the minimum, someone wanting to setup a pirate radio station would need the following pieces of equipment:  - Stereos, CD Players, Microphones, etc. - Audio Amp - Audio Mixer - Transmitter - Aerial      Stations using only the above equipment can sometimes sound quite crude, and might interfere with other legal radio stations.  To avoid this, a 'compressor' can be used, which also limits the noise created by sudden loud noises in the background.      Although any of the example transmitters in this article probably wouldn't be sufficient enough to transmit music audio signals over the air, but they could be used as a starting point to building your own, more efficient kit.  Additionally, FM and AM radio kits can be purchased, which anyone with a soldering iron can build.      The length and height of the antenna depends entirely on how far the radio signals need to be transmitted.  By reading the previous sections, some information on getting a correctly sized aerial can be gained.  For example, a quick and dirty aerial for an AM pirate radio station could be around 15-20 feet tall.      To avoid being busted, it is probably a good idea to stay within the legal power limits.  Otherwise, a Direction Finding device used by the authorities could easily track down the exact location of the transmitter.    ----[ 4.2 -  Wireless Telephone Tapping      'Beige boxing' has long been the easiest and most exploited way to tap telephones, interrupt on neighbours conversations, and use enemies phone lines to make long distance calls to your friend in Australia. However, since beige boxing requires the phreak to lurk around like a ninja, a safer method can be used, which doesn't require you to be physically close to the target phone line.      As expected, audio signals on a target phone line can be transmitted as  radio signals at an arbitrary frequency, and be received by any phreak with  an FM radio receiver.  Although this concept is not new, it serves as an  interesting and useful project for radio newbies to try out.  Below is a  simple FM phone bug transmitter circuit.                    __________________________________________________________                   |                    |                                    |                   |                    |                                    | IN (green) ___.___|_______            |-|                                   |               |   |       |           | |                                   |               |  /\  LED  |           |_|                                   |               |  ---     | |           |___| |      op-amp                  |                |   |   C1 | |           |   | |---|\                         |               |   |       |__________|/      ____| >------- Aerial          | IN (red) _____|___|                  |\ _____|___|/                         |               |   |                    |     |   |                          |                 |   |                    |     |   |                          | OUT (green) __|   |                    (     |   |                          |                  /\                    (     |  /\  varactor                |                  ---                   (     |  ---                         |                   |                    (     |   |                          | OUT (red) ________|____________________|_____|___|__________________________|   - inductor should be about 8 turns of wire - aerial should be about 5 inch long       By interchanging the varator with a crystal, or by using a variable capacitor, the frequency band on which the bug transmits line activity could be changed accordingly.  The varactor making up part of the oscillator circuit is intended to alter the frequency of oscillation, depending on the audio signal inputted from the green wire of the telephone line.  The varactor diode can be thought of as an electrically variable capacitor, which in this case alters its capacitance in sympathy with the audio frequency on the telephone line -- causing for change of oscillation frequency, and thus frequency modulation.       The following op-amp provides additional strength to the signal, in an attempt to avoid a weak, unreliable signal.  For user-friendly purposes, the LED connecting to the red wire of the line pair should illuminate when a signal is present on the line.      The above circuit can be modified to be made more efficient, and a longer aerial is an obvious way of lengthening the range of transmission.  If a phreak was to contruct and use a device like this, all they would need is an FM radio to tune into the correct frequency.  There are much better designs than the minimalistic one above -- if a practical FM telephone bug is required, many plans are available.   ----[ 4.3 - Jamming      Technically, all it takes to carry out 'radio jamming' is to transmit noise at a desired frequency.  For example, if a person in the UK were to transmit RF noise at 30MHz+, police radio communications could possibly disrupted.  Although the principles are mostly the same, there are several different types of jamming.  - modulated jamming   This consists of mixing different types of modulation, and   transmitting the results at a desired radio frequency.  This is   designed to make receiving legimate radio signals hard or next to   impossible.  - CW (continuous wave)   CW jamming only involves transmitting a consistant carrier frequency   once tuned into a RF frequency/band you want to jam.  This again makes   receiving desired radio signals particuarly hard.  - Broadband   Broadband jammers spread Gaussian noise across a whole band of audio   frequencies, blocking legimate audio signals from easy receival.       A basic radio transmitter is easily modifiable, by adding a noise generator, to successfully jam arbitrary frequency bands.  Many other types of radio jammers exist, and their details are readily available on the World Wide Web.   --[ 5 - Conclusion      Radio is an extremely useful technology, which is at least as old as the atom.  But we are only just beginning to exploit its full usefullness in even new and up and coming technology, and probably will do for the next few hundred years.      As we've discovered, contrary to popular belief, employing the use of radio in electronic circuits isn't at all as complicated as one would think.  Because of this, the use of radio and be both used and exploitfully abused -- only a few basic principles need to be understood to make use of this wonderful technology.  Although the surface has only been scratched, and way forward is open.
E-mail me when people leave their comments –

You need to be a member of Peacepink3 to add comments!

Join Peacepink3